The Mold Came Back: An Attic That Was Cleaned, Re-Roofed, and Re-Vented — and Grew Again
Green Building Advisor's Q&A Spotlight follows a Climate Zone 5A attic that had its mold cleaned out, its baffles replaced, its bathroom vents moved, its lights swapped, and its entire roof replaced — and grew mold again around the baffles. The respondents' shared suspect is the one remediation skipped: indoor air leaking into the attic through the ceiling.
Setting: a cold-climate house (Climate Zone 5A); the building-science lesson is general, and the gym application is ours and is labelled as such. Source score: 8/10. This page is our original summary of the article’s published case account. The article’s full expert discussion sits behind Green Building Advisor’s Prime membership; this summary is built only from the case facts and framing the article publishes openly, and it says so. It is general information, not legal or medical advice.
Source: Green Building Advisor, “Recurring Mold in the Attic” — Q&A Spotlight by Chuck Bickford, April 15, 2024, working from homeowner “MattJE’s” Q&A post.
The case, as the article publishes it
Five years before the article, the homeowner bought a house in Climate Zone 5A whose attic was already mold-infested. What followed, in the article’s account, is the full conventional remedy list — executed, not skipped:
- The mold was cleaned out.
- The plastic baffles that form the ventilation channel from soffit to ridge were replaced.
- Cellulose insulation was installed.
- The general contractor moved the bathroom vents from the soffits to the roof.
- All the can lights were replaced with LED retrofits.
- Later the same year, the entire roof was replaced, the new assembly including an ice-and-water-shield underlayment.
And the mold returned — mostly around the baffles. The article’s evidence list is a moisture inventory, printed as the homeowner reported it: rusty roofing nails protruding through the deck, water on the exterior wall top plates, and condensation on the underside of the baffles. No apparent roof leaks. Thermal imaging showed no areas of heat entering the attic from below that it could reveal. The homeowner’s own suspect — a ridge vent cut, in his measurement, 3 inches wide on either side of the ridge, possibly imbalancing the airflow, with soffits vented only every third rafter bay — is carried in the article as his question, not as a verdict. He had already consulted roofers, insulation contractors, and mold remediation companies, in his account, without getting closer to a solution.
The mechanism the article leads with
The article’s own framing, in its opening and its photo caption, states the physics plainly: if attic air is humid and the roof sheathing is cold, condensation or frost accumulates on the underside of the sheathing — and the source of attic moisture is usually indoor air entering the attic through cracks in the ceiling. Its section heading compresses the same point: warm air plus cold surfaces equals condensation, and mold. The responses the article previews center on air leakage — the named respondents converge on moist indoor air getting into the attic as the problem to hunt. The full exchange is Prime-gated; this page does not invent its contents. But the published framing alone carries the lesson whole, because the case itself proves the negative: cleaning, vent hardware, insulation, and a new roof were all replaced, and none of them is the air seal. A ceiling plane full of penetrations — lights, hatches, chases, top plates — can feed an attic more moisture than its vents can remove, and every cosmetic and ventilation fix downstream of that leak will be outrun by it.
That is the same doctrine, in a roof, that our hidden-mold curation states for walls and that the clearance-timing curation states for remediation sign-off: growth that returns on schedule after cleaning is not a cleaning failure. It is an unfixed moisture pathway announcing itself, on schedule.
Why it matters here — the gym application, in our words
Translate the attic into the room this site exists for. A sauna or locker-room wet area is a warm, humid box pressed against cooler construction — the same warm-air/cold-surface pairing, run daily at far higher moisture loads. The Daytona founding case’s build is the attic case in gym form: a sealed bench cavity and wet-room air with somewhere cold to go. When a gym’s answer to visible growth is bleach, paint, and a new ceiling tile — the equivalent of this homeowner’s cleaning, baffles, and roof — the growth’s return date is set by the pathway nobody sealed, not by the product somebody sprayed. The diagnostic question this article teaches is the one to put to any operator, in writing, with a date on it: where does this room’s wet air actually go, and what cold surface does it meet on the way?
Tools for this job: Measure — moisture is the whole game
Pinless moisture meter
What it is: A handheld meter that reads moisture inside drywall, wood, and flooring through the surface — no pinholes, no damage. The tool that finds the wet wall behind the paint.
Why it is listed: Moisture readings are the hardest evidence to argue with. A dated photo of a meter reading on a wall turns a landlord dispute from opinion into documentation.
Its limits: Readings are relative and material-dependent — use them comparatively (wet spot vs. known-dry spot) and record both. A meter finds moisture, not mold.
Thermo-hygrometer / humidity data logger
What it is: A room thermometer-hygrometer; the logging kind records humidity over days and weeks instead of showing a single moment.
Why it is listed: A log beats a snapshot. Two weeks of humidity history above 60% is a document; a glance at a dial is an anecdote.
Its limits: Cheap sensors drift — sanity-check a new unit against a second one. Placement matters: measure where people live and sleep, not next to a shower door.
Some links in this strip are affiliate links and cost you nothing extra if you buy through one. As an Amazon Associate I earn from qualifying purchases. Affiliate money never buys scores, coverage, or silence — see our affiliate disclosure.
Read what is published openly at the source: Green Building Advisor — Recurring Mold in the Attic (full Q&A discussion is a GBA Prime article, as the source page states).
If this happened to you
Growth that returns to the same spot after a documented cleaning is worth more, as evidence, than growth found once — it dates the pathway. File a report with both dates: when it was cleaned, and when it came back.
Not professional advice. This page summarizes one published case account for general information; the source article’s full expert discussion is membership-gated and is not summarized here beyond its published framing. Building-specific diagnosis belongs to building professionals.